With the drive to farm sustainably, be sure to capitalise on the excellent potential in this year’s forage maize crops as a high-energy, home-grown feed for dairy cows and finishing beef cattle.
Do this by minimising nutrient losses and wastage when turning maize crops into silage.
Those are the messages from Volac business manager, Liam Gannon, who said this season has set the scene for some very good maize crops.
However, maize can harbour a range of undesirable microbes – e.g. on dying leaves and on rotting tassels that collect in leaf joints – which can feed on its nutrients and interfere with preservation in the clamp.
“Unless prevented, undesirable bacteria, yeasts and moulds can cause losses equivalent to between one and two trailer loads of dry matter out of every 10 trailer loads ensiled,” said Liam.
“More importantly, losses aren’t just the least nutritious parts of the dry matter. They are likely to be sugars and starches, which are the main energy sources that maize is grown for.”
To help farmers minimise losses and lock-in the maximum sustainability benefits of maize, Volac has prepared a five-point checklist of some best practice harvest and ensiling tips.
1. Harvest maize at its peak
Maize is often regarded as only ready to harvest once it dies back, but the optimum is as soon as it reaches 30-33% dry matter content, Liam said, which is usually while it is still green.
Waiting longer can increase starch in the cobs. You also run the risk of deteriorating weather and soil conditions as the year progresses, which can negatively impact on maize quality.
However, if this is at the expense of leaves dying back, then the plant will become less digestible to the cow. Also, this dead leaf tissue harbours yeasts and moulds.
“Monitor the crop’s increasing dry matter regularly,” Liam urged.
“That way, you can give your contractor advanced notice of when 30-33% dry matter is likely to be reached.”
2. Avoid the fermentation trap
Avoid the trap of thinking maize always ferments efficiently. It can typically lose nearly a tenth of its dry matter through inefficient fermentation, said Liam, and inefficient fermentation bacteria feed on sugars, so the metabolisable energy of the remaining silage will also be lower.
Take steps to improve fermentation, e.g. by applying a proven bacterial additive. In trials, an additive containing the efficient fermentation bacterium Lactobacillus plantarum MTD/1 has cut dry matter losses by half.
3. Head-off heating (aerobic spoilage)
As well as fermentation losses, maize silage is prone to similar losses from heating – caused by yeast and mould growth in the presence of air.
Airtight conditions in the clamp are crucial to minimise these losses, Liam said, but this alone is not always sufficient, particularly in clamps with wider faces which, once opened, are exposed to air for long periods of time.
“Applying a dual-acting bacterial additive allows you to target both problems,” he said.
“Ecocool, for example, contains MTD/1 bacteria for fermentation, plus Lactobacillus buchneri PJB/1 to inhibit yeast and moulds. It has been shown to keep maize silage cool and stable for more than 10 days.”
4. Clamp down on consolidation
Do not compromise clamp consolidation. It can be tempting if in a rush, Liam acknowledged, but you could be living with the consequences of poor preservation from air in the clamp for a long time.
Shorter chop lengths are useful to aid consolidation, especially if maize is dry. So consider chopping to 1.2-2.2cm.
Also, fill clamps at a maximum angle of 20° to the horizontal and in layers at most 10-15cm deep, to get maximum benefit from the compaction machinery.
Typically, maize at 30% dry matter requires 25% of its weight arriving at the clamp per hour to consolidate it. So, 100t/hr requires 25t, which means at least two machines rolling constantly.
5. Keep out air
Once air has been squeezed out, keep it out by creating as much of an airtight bag in the clamp as possible, Liam said.
In practice, he said this means lining the walls with polythene side sheets down to the ground because concrete can be porous and placing an oxygen barrier film on top of the maize, which ‘clings’ to it to seal the surface and protects the top from bird damage with zill silage covers and bags.
Side sheets should have at least a 1m overlap on top of the oxygen barrier film, before the top sheet is pulled tight over the oxygen barrier film. Use a heavy, woven sheet over the top sheet to protect against damage, followed by plenty of weight.
Remember, clamp bases rarely suffer from heating and spoilage simply because the weight of the silage above.
For more information on producing consistently better maize silage, contact Volac.
